![]() ![]() ![]() Test mode (TCP/IP terminal with TEA authorization support and NVT (Network virtual Terminal) parser for remote I/O pins control.UDP Config utility (IP, Port, MASK, GW setting).TCP/IP Client terminal (similar to "Telnet").Serial port terminal (COM5 and higher support).For this, I hoped I could use time, as in time bash -c '.' Would be some command I could run.Now, the first problem is that I want to use the device at 2000000 bps, so I cannot use or (they both seem to go up to 115200 bps only).Hercules is great utility if you are working with the serial and Ethernet devices & interfaces. I have a serial device set up as loopback (meaning it will simply echo back any character it receives), and I'd like to measure effective throughput speed. Older serial drivers (2001?) used justtty00, tty01, etc.The tables below shows some examples of serial device names. For details seeModem-HOWTO, section: cua Device Obsolete.For creating the old devices in the device directory see:Dos/Windows use the COM name while the messages from the serial driveruse ttyS00, ttyS01, etc. You may still have the cua devices inyour /dev directory but they are now deprecated. The cua major number was 5 andminor numbers started at 64. For example, ttyS2 would correspond tocua2. Tofind the device names for various devices, see the 'devices' file inthe kernel documentation.There formerly was a 'cua' name for each serial port and it behavedjust a little differently. You can see this (and theminor numbers too) by typing: 'ls -l ttyS.' ![]() The serial portttySx (x=0,1,2, etc.) is major number 4. Instead, they areeither ISA, on an internal ISA bus or on a LPC bus which is intendedfor slow legacy I/O devices: serial/parallel ports and floppy drives.Devices in Linux have major and minor numbers. ![]() Even for all-PCI-slotmotherboards, the serial ports are often not PCI. Forexample, to change the name of what the kernel detects as ttyS3 towhat you want to name it: ttyS14, add a line similar to this to/etc/udev/lesBUS'pci' KERNEL'ttyS3',NAME='ttyS14'On-board serial ports on motherboards which have both PCI and ISAslots are likely to still be ISA ports. It's not requiredto be this way but it often is.If you're using udev (which puts only the device you have on yourcomputer into the /dev directory at boottime) then there's an easy wayto change the device names by editing files in /etc/udev/. 0-1 (or 0-3) are reserved for the old ISA bus (or thenewer LPC bus) and 2-upward (or 4-upward or 14-upward) are used forPCI, where older schemes are shown in parentheses. But since most PCs only came with one or two serial ports,ttyS0 and possibly ttyS1 (for the second port) the PCI bus can now usettyS2 (kernel 2.6.15 on).Īll this permits one to have both ISAserial ports and PCI serial ports on the same PC with no nameconflicts. Multiport serialcard used somewhat differnt names (depending on the brand) such as/dev/ttyE5.Since DOS provided for 4 serial ports on the old ISA bus:COM1-COM4, or ttyS0-ttyS3 in Linux, most serial ports on the newer PCIbus used higher numbers such as ttyS4 or ttyS14 (prior to kernel2.6.13). Thenaround the year 2000 came the USB bus with names like /dev/ttyUSB0 and/dev/ttyACM1 (for the ACM modem on the USB bus). Serial HOWTO: Serial Port Devices /dev/ttyS2, etc.Common serial port names are /dev/ttyS0, /dev/ttyS1, etc. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |